WHY UNDERSTANDING PLUMBING BASICS IS ESSENTIAL WHEN INSTALLING A BATHTUB

Why Understanding Plumbing Basics is Essential When Installing a Bathtub

Why Understanding Plumbing Basics is Essential When Installing a Bathtub

Blog Article

Call

Presented here in the next paragraph yow will discover some high-quality ideas involving How to Install a Bathtub.


How to Install a Bathtub
Setting up a bath tub isn't exactly rocket science, but it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult project. If the old bathtub is conveniently obtainable, the job can move rapidly; if you have to open a wall surface to eliminate the old bathtub and also position the brand-new tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and also embeded in the new one. Make certain you have qualified yourself for the work and also are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed project, it is better to take into consideration using one before you start. Opportunities are you might need an expert plumber to make tube links.
This write-up will help you mount a new bath tub in your restroom if you have actually currently acquired a new tub as well as don't need to change the plan of your previous water supply pipelines.
Your devices as well as product list should comprise the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Installation


    First of all, the supporting structure provided with the bath ought to be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to prevent stress on the bath tub.
    Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of every one of the provided washing machines.
    Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its last setting.

    Removing Old Taps


    If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the water supply. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be fairly problematic due to the restricted access that is usually the situation.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
    Prior to carrying on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

    Mounting the Bath tub


    Using both wood boards under its feet, place the bath tub in the required placement. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little points.
    The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the level as well as adjusting the feet on the bath tub until the level reads degree.
    To set up faucets, fit all-time low of the outermost versatile tap adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the other faucet.
    Switch on the water supply and examine all joints as well as new pipework for leakages and also tighten them if needed. Fill up the tub as well as additionally check the overflow outlet and also the regular electrical outlet for leakages.
    Lastly, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait until the tub has been utilized a minimum of when as this will resolve it into its final setting.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipes.
    If you need to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place between the tap and the sink. Safeguard the tap in position with the maker supplied backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous type must be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the location where the bathroom satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, causing the water to permeate the wall surface between the bath and the tiling, causing complications with dampness and also feasible leaks to the ceiling below.
    You can choose from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealant can break rather early if you do not think about this movement before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof glue and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    As a keen person who reads on Installing A Bathtub, I think sharing that excerpt was beneficial. Sharing is nice. You never know, you will be helping someone out. Thanks a lot for your time. Please pay a visit to our site back soon.


    Rates

    Report this page